| Clause | Measurement/testing | Testing / measuring equipment / material needed | Subcontracting |
| 2 | Normative References | Access to copies of listed standards | R |
| 4 | General requirement | None | |
| 5 | General conditions for the tests | None | |
| 6 | Classification | None | |
| 7 | Marking and instructions | Petroleum spirit | R |
| 8 | Protection against access to live parts | Test probe B, 13 and 41 of IEC 61032, voltmeter, mill-ammeter,
oscilloscope, force gauges, 2000 ohm non-inductive resistor, Coulometer,energymeter | R
S |
| 9 | Starting of motor-operated appliances | None | |
| 10 | Power input and current | Chronometer, Voltmeter, ammeter, wattmeter | R |
11 |
Heating | Temperature controlled room,Temperature Recorder, Fine wire
thermocouples, Test corners, Winding resistance measurement system, Probe for measurement of surface temperature | R
R |
| 12 | Void | | |
| 13 | Leakage current and electric strength at operating temperature | Metal foil, Leakage current meter, Isolation transformer, HV test
supply, Network (Fig.4 of IEC60990) | R |
| 14 | Transient overvoltages | Impulse voltage test generator and monitor | S |
| 15 | Moisture resistance | IP test equipment, Measurement beaker, Spray nozzle (for testing appliances that cannot be placed under the oscillating
tube specified in IEC 60529) as appropriate according to the requirement of Part 2s(Only when the second
numeral more than “0” is given) NaCl, Rinsing agent Humidity cabinet capable of (93 ± 3)%RH at selected temperature
with HV test facilities | R
R R |
| 16 | Leakage current and electric strength | Metal foil, Low impedance ammeter, HV test supply | R |
| 17 | Overload protection of transformers and associated circuits | Included above | |
19 |
Abnormal operation | Electrostatic discharge test apparatus (IEC 61000-4-2), Radiated
field test apparatus (IEC 61000-4-3), Fast transient burst test
apparatus (IEC 61000-4-4), Voltage surge test apparatus (IEC
61000-4-5), Injected current test apparatus (IEC 61000-4-6),
Voltage dip and interruption test apparatus (IEC 61000-4-11), Mains
signal test apparatus (IEC 61000-4-13) |
S |
| 20 | Stability and mechanical hazards | Inclined plane, masses, force gauges, test probe similar to test probe B of IEC 61032 with circular stop
face 50 mm Ø | R |
| 21 | Mechanical strength | Spring hammer, Hardened steel pin, Force gauges | R |
22 |
Construction | Test rig for torque on pin supported appliance, Heating cabinet
(70°C ±2°C), Test probe 11 of IEC 61032, Test fingernail (Figure 7), Force
gauge, Oscilloscope and test probe according to DSH 716 Pressure test apparatus Automatic cord reel test apparatus Oxygen bomb with pressure apparatus Methylated spirits Small parts cylinder in Figure 13 | R
R S S S R |
| 23 | Internal wiring | Flexing test apparatus | R |
24 |
Components | Laboratory may or may not have facilities for testing to component
standards. Certification by specialist laboratories is accepted for compliance |
S |
| 25 | Supply connection and external flexible cords | Flexing test apparatus, Cord anchorage force & torque tester | R |
| 26 | Terminals for external conductors | Torque screwdriver | R |
| 27 | Provision for earthing | Earth continuity tester, access to ISO2178 and ISO1463 testing | R |
| 28 | Screws and connections | Torque gauge | R |
| 29 | Clearances, creepage distances and solid insulation | Mechanical measurement tools, Rod or ball gauges, Proof tracking test apparatus | R
|
30 |
Resistance to heat and fire | Ball Pressure test apparatus, Glow wire & Needle flame test
apparatus, Apparatus for low power circuit determination. Horizontal and vertical burning test apparatus ISO 9772 test apparatus | R
S S |
| 31 | Resistance to rusting | Part 2 requirements | |
| 32 | Radiation, toxicity and similar hazards | Part 2 requirements | |
| Annex A | Routine tests | None | |
| Annex B | Appliances powered by rechargeable batteries | Free fall test apparatus (IEC 60068-2-31, Procedure 2) | S |
| Annex C | Ageing test on motors | Nothing special | |
| Annex D | Thermal motor protectors | Nothing special | |
| Annex E | Needle flame test | Needle flame test apparatus (IEC 60695-11-5) | R |
| Annex F | Capacitors | Impulse voltage test apparatus, Endurance test apparatus (IEC
60384-14) | S |
| Annex G | Safety isolating transformers | As required by part 2's | |
| Annex H | Switches | Endurance test apparatus (IEC 61058-1) | S |
| Annex I | Motors having basic insulation that is inadequate for the rated
voltage of the appliance | Nothing special | |
| Annex J | Coated printed circuit boards | Coated printed circuit boards test apparatus (IEC 60664-3) | S |
| Annex K | Overvoltage categories | None | |
| Annex L | Guidance for the measurement of clearances and creepage distances | None | |
| Annex M | Pollution degree | None | |
| Annex N | Proof tracking test | Proof tracking test apparatus (IEC 60112) | R |
| Annex O | Selection and sequence of the tests of Clause 30 | None | |
| Annex P | Guidance for the application of this standard to appliances used in
warm damp equable climates | None | |
| Annex Q | Sequence of tests for the evaluation of electronic circuits | None | |
| Annex R | Software evaluation | Capability for Software evaluation (IEC 60730-1) | S and see Note 1a and 1b |
| Annex S | Battery-operated appliances powered by batteries that are
non-rechargeable or not recharged in the appliance | Power supply | R |
| Annex T | UV-C radiation effect on non-metallic materials | Testing apparatus related to UV-C radiation | S |
